Solid wood furniture is known as our furniture is an indispensable, but we on the solid wood furniture production technology process is poorly understood, then the following, Xiaobian is revealed solid wood furniture with production process for us.
1 sheet is dry, the moisture content of the wood is controlled in 8%~10%, without the average moisture content of the wood that is dry lumber is above 50%, the wood is not easy to present the scene such as burst deformation.
2 balance, the dry off of wood and natural place for a few days, so that the recovery of wood balance.
3 material ingredients, wood products can be divided into parts according to their appearance materials, internal materials and three kinds of dark material. Appearance materials exposed to the outside, such as office table, cabinet visible part; the internal materials to internal WIP, such as files, bottom slab, etc.; dark materials refers to the parts that you can't see in the normal use, such as drawer slideway, panelling, lining and so on. Pay attention to material knots, internal crack, blue, wood, end split.
4 rough planing, for wool plate thickness.
5 wind shear, sheet finishing wool length. Blanking according to the desired length of longer 20mm.
6 trimming, flash cannot be used on wool cut sheet.
7 distribution board, wood board material selection points straight lines, mountain lines, color matching with the common, with the width of the distribution of the required width of a reasonable discharge margin. Finish to end crack, internal crack, knurr, blue, rot off.
8 cloth glue, evenly distributed in the wood glue, glue ratio: curing agent (15 - 10 grams), the fight board plastic (100 grams), 500 grams each time.
9 jigsaw puzzle machine, the use of wood will be assembled, jigsaw, convex differential length difference, eye color, knurr.
10 aging, cloth glue the end of the wood placed 2 hours or so, so that the glue.
The remaining 11 sand planing, planing to glue between the wood, the wood surface without residual glue.
12 cut and fixed width, with a single chip to set the width of the wood.
13 surrounded by plane, according to the shape of the need to dig out the wood.
14 health, will be a natural wood placed 24 hours.
Two: the carpenter
1. Wide sand thickness, according to the request of sand check fit request processing scale and machine added after the end of polishing sand, coarse sand and a sand 0.2mm, polishing a sand 0.1mm.
2. Fine cut, to give wool length and processing do no collapse stubble, black, long and wide machining error does not exceed 0.2 mm, 1 m below the diagonal is less than or equal to 0.5 mm, 1 m above the plate diagonal should be equal to or less than 1mm.
3 molding, according to the drawings will be wood processing. Processing does not allow collapse stubble, burr, jump knife and black phenomenon, the parts machined surface should be lubrication, flat, line is fluent, before processing view equipment parts, screw loosening, template is not the standard device, tool is not impaction, machining process in the suppression of Shun Dao feed and assembly scale error does not exceed 0.2mm.
4. Drilling, according to technical drawings request drilling, processing do no collapse, no thorn scene, hole machining error must not exceed 0.2mm, merchandise to do the drilling matching, often try to install, frequently check and ensure product quality.
5 accessories bolt sand, sand light accessories, sanding good products should be flat, no sand marks, the edge of the common corner. Sand detection before the use of parts of the first to understand the orientation, the first sand after sand.
Group, group not apart of the components in the group of should first preparation, all to assemble according to the drawings processing request to see correct, components without collapsed, burr, black phenomenon, beginning first installed after scaling and technical drawings there is no margin for error conditions. Group in the process of the glue evenly coated, the group made a good semi products, should be no nails, missing nails, combined with tight, glue scrub to clean.
7 big group, test assembly parts view and drawings are not wrong. The difference between the group and the group is the end of the large group of products after the end of the.
8 products seized sand, the products will be sand light, to achieve flat, no sand marks, the edge of the common corner.
9 balance, the component natural place for a period of time.
10 painting on the line inspection, the workpiece surface from scratch again, especially the appearance of wood capillary fibers. Together to see the shortcomings of the white body is not now handled well, such as: poor repair, sanding, cracking, deformation, etc..
11 blow the dust, the dust on the surface of the work piece blow clean.